Machinery Directive 2006/42/EC: certification and CE marking | Istituto Giordano
Giuseppe Persano Adorno
CONTACTS

Giuseppe Persano Adorno
Tel. 0541 322.232
E-mail g.persano@giordano.it

Machinery Directive 2006/42/EC: certification and CE marking

Directive 2006/42/CE and Regulation (EU) 2023/1230

Istituto Giordano is a Notified Body (No. 0407) authorised to carry out conformity assessment and certification activities under Directive 2006/42/EC. These activities are performed under ACCREDIA accreditation in accordance with UNI CEI EN ISO/IEC 17065.

Drawing on its extensive expertise in product testing and certification, Istituto Giordano is a qualified partner for manufacturers undertaking machinery certification and CE marking, providing technical expertise, assessment activities and laboratory testing.


View all Accreditation Certificates (No. 00019) on the ACCREDIA website.  

 

From the Machinery Directive to the new Regulation (EU) 2023/1230

European legislation governing machinery is currently undergoing a transition.

The Machinery Directive 2006/42/EC will remain the applicable reference for machinery placed on the market until 19 January 2027. From 20 January 2027, the new Regulation (EU) 2023/1230 will apply, replacing the Directive.

The new Regulation introduces significant changes for manufacturers and economic operators. It also updates the provisions governing conformity assessment procedures and the categories of machinery for which the involvement of a Notified Body is required.


Which products are covered by the Machinery Directive?

Subject to the exclusions laid down in the legislation, Directive 2006/42/EC applies to several product categories, including:

  • machinery;
  • interchangeable equipment;
  • safety components;
  • lifting accessories;
  • chains, ropes and webbing;
  • removable mechanical transmission devices;
  • partly completed machinery.


Before starting a conformity assessment process, it is therefore necessary to determine whether the product falls within the scope of the Directive and which procedure must be applied.

Depending on the type of machinery, the harmonised standards applied and the applicable procedure, the involvement of a Notified Body may be required.

Within the scope of Directive 2006/42/EC, Istituto Giordano performs conformity assessment and certification activities in accordance with its notified scope.

Depending on the applicable procedure, these activities may include:
 

  • examination of the machinery technical documentation;
  • verification of the applicable essential health and safety requirements (EHSRs);
  • assessment of the technical standards applied;
  • inspections, checks, measurements and tests, where necessary;
  • assessment of a representative model of the machinery as part of the EC type-examination procedure;
  • issuance of the certification required under the applicable procedure;
  • assessment and surveillance of the full quality assurance system, where required by the Directive.
 

Annex IV to the Machinery Directive

Annex IV to Machinery Directive 2006/42/EC identifies specific categories of machinery for which particular conformity assessment procedures are laid down.

The applicable procedure also depends on the use of harmonised standards and on whether those standards cover all relevant essential health and safety requirements.

For machinery listed in Annex IV, where provided for by the Directive, the manufacturer may or must use conformity assessment procedures involving a Notified Body.

These include EC type-examination, as laid down in Annex IX, and the full quality assurance procedure laid down in Annex X.

EC type-examination – Annex IX

EC type-examination is the procedure whereby a Notified Body verifies and certifies that a representative model of machinery belonging to one of the categories listed in Annex IV satisfies the applicable provisions of the Directive.

As part of the procedure, the Notified Body examines the technical file and carries out, or arranges to have carried out, the necessary checks, measurements and tests.

Where the type satisfies the provisions of the Directive, the Notified Body issues an EC type-examination certificate.

Full quality assurance – Annex X

The full quality assurance procedure applies to machinery referred to in Annex IV that is manufactured using a quality system covering design, manufacture, final inspection and testing.

The Notified Body assesses the quality system implemented by the manufacturer and monitors its application in accordance with the requirements of the Directive.

Istituto Giordano also operates within the scope of Annex X to Machinery Directive 2006/42/EC.


CE marking of machinery: what are the manufacturer's obligations?

Before placing machinery on the market and/or putting it into service, the manufacturer or its authorised representative must fulfil the obligations laid down in Directive 2006/42/EC.

In particular, the manufacturer must:

  • ensure that the machinery satisfies the relevant essential health and safety requirements;
  • carry out a risk assessment;
  • prepare the technical file;
  • provide the necessary information and instructions for use;
  • apply the appropriate conformity assessment procedure;
  • draw up and sign the EC Declaration of Conformity, which certifies that the machinery meets all applicable requirements of the Directive;
  • affix the CE marking to the machinery.

CE marking is therefore not simply a graphic symbol: it represents the outcome of a process through which the manufacturer ensures and declares that the machinery complies with the applicable European legislation.


EC Declaration of Conformity for machinery

The EC Declaration of Conformity is one of the key documents required under the Machinery Directive.

Through this document, the manufacturer — or, where applicable, its authorised representative — declares under its sole responsibility that the machinery complies with the applicable provisions.

It is important not to confuse the EC Declaration of Conformity, which is the responsibility of the manufacturer, with any certificate issued by a Notified Body as part of a specific conformity assessment procedure.

The involvement of a Notified Body therefore does not transfer to the Notified Body the manufacturer's overall responsibility for the conformity and CE marking of the machinery.


Machinery Directive technical file and mandatory documentation

One of the key elements in demonstrating machinery compliance is the correct preparation of the technical file.

The technical file must make it possible to demonstrate that the machinery complies with the requirements of the Directive and must include, as applicable, information relating to its design, manufacture, risk assessment and the solutions adopted to ensure safety.

The documentation may include, among other items:

  • a general description of the machinery;
  • overall drawings of the machinery and drawings of the control circuits;
  • detailed drawings and information required to verify conformity;
  • risk assessment documentation;
  • a list of the applicable essential health and safety requirements;
  • harmonised standards and other technical specifications applied;
  • technical reports and test results;
  • instructions for use;
  • a copy of the EC Declaration of Conformity.

The contents of the technical file must be determined according to the machinery concerned and the applicable requirements.


Machinery risk assessment

Risk assessment is a fundamental step in achieving compliance with the Machinery Directive.

The manufacturer must identify the hazards associated with the machinery and assess the risks by taking into account the various stages of its life cycle, its intended use and any reasonably foreseeable misuse.

Based on this analysis, the necessary measures must be identified and implemented in order to eliminate hazards or reduce risks.

In accordance with the principles of safety integration, the process involves:

  1. eliminating or reducing risks as far as possible through inherently safe design and construction;
  2. implementing the necessary protective measures in relation to risks that cannot be eliminated;
  3. informing users of residual risks and indicating any necessary safety measures.

One of the main technical standards used for machinery risk assessment and risk reduction is EN ISO 12100.


Partly completed machinery and Declaration of Incorporation

Directive 2006/42/EC also covers partly completed machinery, i.e. assemblies which are almost machinery but which cannot in themselves perform a specific application.

Partly completed machinery is intended to be incorporated into or assembled with other machinery, other partly completed machinery or equipment, thereby forming machinery to which the Directive applies.

Before partly completed machinery is placed on the market, the relevant technical documentation, assembly instructions and the Declaration of Incorporation required by the Directive must be prepared.


Machinery manufactured for own use: what obligations apply?

The obligations laid down in the Machinery Directive may also apply to machinery manufactured by a company for direct use within its own operations.

The legislation also covers putting into service, meaning the first use, for its intended purpose, in the European Union, of machinery covered by the Directive.

The fact that machinery is manufactured for the manufacturer's own use and is not sold to third parties does not therefore automatically exclude it from the obligations laid down in the legislation.

Each case must be assessed individually in order to identify the applicable legislation and determine the requirements that must be fulfilled to ensure conformity.


F.A.Q.

Who can certify machinery?

This depends on the machinery concerned and on the applicable conformity assessment procedure. Responsibility for conformity and CE marking lies with the manufacturer. Where the Directive requires third-party conformity assessment, this must be carried out by a Notified Body authorised for the relevant activity.

What is Annex IV to the Machinery Directive?

Annex IV to Machinery Directive 2006/42/EC identifies specific categories of machinery for which particular conformity assessment procedures are laid down. To interpret this Annex correctly, it is essential to understand the machinery categories listed and the specific procedures required, which may vary according to the type of machinery and its intended use. Depending on the conditions established by the Directive, these procedures may require the involvement of a Notified Body.

What documents are required for CE marking of machinery?

The required documentation includes, among other elements, the technical file, risk assessment, instructions, documentation relating to the standards and technical specifications applied, and the EC Declaration of Conformity. The documentation required must be determined according to the machinery concerned and the applicable legislation.

When will the new Machinery Regulation apply?

Regulation (EU) 2023/1230 will apply, for the majority of its provisions, from 20 January 2027 and will replace Directive 2006/42/EC.

For further information on the changes introduced and the relevant timeline, see our dedicated article on the new Machinery Regulation (EU) 2023/1230.





 
Request a quote