Materials and components may undergo changes in their properties due to exposure to solar radiation, temperature, humidity, corrosive agents or repeated mechanical stresses. Accelerated ageing tests reproduce defined and controlled conditions in the laboratory to investigate these phenomena within timeframes compatible with product development, qualification and quality control activities.
The results do not automatically provide a direct prediction of service life under real-world conditions. Instead, they enable the comparison of different solutions, the assessment of performance retention and the collection of experimental evidence on specimen behaviour under the conditions specified by the test method.

Depending on the testing objectives, accelerated ageing tests can help to:
compare materials, treatments, coatings or product variants;
investigate changes in appearance, dimensions, mechanical properties, electrical characteristics or functionality;
assess performance retention before and after exposure;
identify potential design or manufacturing weaknesses;
support research and development, quality control and technical qualification activities.

Ultraviolet radiation can affect the appearance and properties of polymers, paints, coatings, composite materials, seals and other products intended for exposure to light.
UV Resistance and Condensation Tests are performed using specialised equipment, such as UV fluorescent lamp chambers or xenon-arc exposure systems, capable of simulating different components of solar radiation.
During exposure, parameters specified by the applicable test method are controlled, including irradiance, temperature, exposure duration and the presence of humidity, condensation or water. Assessments may include:
colour changes and yellowing;
loss of gloss;
microcracking, surface cracking or other surface deterioration;
changes in elasticity or brittleness;
changes in mechanical properties.
Variations in temperature and humidity can cause thermal expansion and contraction, condensation, deformation and changes in performance. Climatic chambers make it possible to reproduce controlled environmental conditions and repeated sequences of heating, cooling and relative humidity variations.
When the test method involves rapid transitions between different temperatures, the procedure is referred to as thermal shock testing. Depending on the product, assessments may include:
dimensional changes and deformation;
cracking caused by thermal stresses;
changes in electrical or mechanical properties;
integrity of joints and assemblies;
retention of functionality.
For metallic materials and protective coatings, accelerated corrosion tests make it possible to investigate specimen behaviour in controlled atmospheres.

In salt spray testing, a saline solution is atomised inside a test chamber under specified conditions. Other test methods may involve alternating phases of salt spray exposure, humidity, drying and temperature variations.
Depending on the applicable specifications, these tests can be performed on structural metalwork, windows and doors, fasteners, automotive components and products intended for outdoor or marine environments.
Sulphur dioxide (SO₂) is a corrosive agent that may be present in industrial atmospheres and other environments characterised by specific exposure conditions. Tests conducted in sulphur dioxide-containing atmospheres, commonly referred to as Kesternich tests, make it possible to assess the behaviour of metallic materials, protective coatings, painted surfaces and other products exposed to humid, corrosive environments.

Compared with salt spray testing, the corrosive agent is different, resulting in different test conditions and degradation mechanisms to be investigated.
Ozone can cause deterioration in elastomers, rubber, plastics and other materials susceptible to oxidation. Ozone resistance tests expose specimens to a controlled atmosphere, with ozone concentration, temperature, exposure duration and strain conditions defined by the applicable test method.
The test does not necessarily involve repeated cycles. In many cases, exposure takes place under constant conditions, but at ozone concentrations higher than those normally found in the environment, thereby accelerating the degradation process.
During service, materials and components may come into contact with fuels, lubricating oils, solvents, detergents, acids, alkalis, alcoholic solutions or other fluids. Immersion tests make it possible to assess specimen behaviour following controlled exposure to substances relevant to the intended application.
For example, a hose, seal or component intended for installation near an engine may require testing to verify its resistance to oils, fuels or other operating fluids.
During service, many products are subjected to repeated movements, loads or operating cycles. Opening and closing operations, rotations, vibrations or cyclic force applications can lead to wear, loosening, deformation or fatigue-related damage.

Cyclic mechanical durability tests reproduce predefined operating sequences using test equipment configured according to the characteristics of the product. These tests can assess:
fatigue resistance;
wear of moving components;
retention of functionality;
permanent deformation;
initiation of cracks or occurrence of fractures;
behaviour of joints and fastening systems.
The number of cycles, stress levels, operating procedures and acceptance criteria depend on the product type and the applicable technical specifications.
During transportation or service, products and components may be subjected to continuous or intermittent vibrations. Vibration tests apply defined excitation profiles, such as sinusoidal or random vibrations, to investigate potential loosening, damage to connections, fatigue phenomena or loss of functionality.
The test configuration depends on the product, the excitation profile and the assessment objectives. Before testing, it is therefore necessary to define the test axes, frequencies, excitation levels, duration, mounting conditions and functional checks.
Contact the technical experts at Istituto Giordano to identify the most appropriate test methods based on your product's characteristics and intended application.